EDK M100BP portable multi-component biogas analyzer
Analysis CO2 CH4 O2 H2S | Low-cost solution |
Measuring CO2 and CH4 via Nondispersive infrared technology NDIR | Portable battery-powered version |
Long-life hydrogen sulfide sensor with automatic air purifier | Modbus、Profibus、Ethernet(optional) |
ARM processor | Automatic zero adjusting |
Touch screen display | Data downloadable via SD card |
Ethernet and USB remoting |
|
EDK M100BP series multi - gas analyzer produced by ETG company. Because of their accuracy, stability, reliability, wide range and multifunction, it is the best choice for biogas measurement and industrial combustion analysis.
Unlike other analyzers, EDK M100B non-dispersive infrared (NDIR) gas analyzers use a single optical path measurement platform to detect a variety of gases. When using methane as a biofuel, a single gas analyzer is not available because the gas usually contains a large amount of CO as a pollutant. In addition to methane, the EDK analyzer can also measure CO2, CO and O2, thus providing the best combination of gas analysis for combustion optimization.
After initial warm-up, our enhanced optical and electronic NDIR analyzer truly eliminates zero drift. Range drift in many other NDIR instruments is eliminated by means of temperature and pressure compensation.
EDK M100BP multi-component biogas analyzer
Measuring Method | Gas | Resolution | Range | Accuracy | Precision | Response Time |
NDIR | CH4 | 0.01% | 0-M100BP% 0ppm-100% 40-80% 80-M100BP% | +/‐ 1% F.S +/- 2% actual value +/- 1% actual value +/- 5% actual value | +/- 0,8% | T90 & T10<10 s |
NDIR | CO2 | 0.01% | 0-50% 0.00-16.00% 16.01-20.00% | +/- 0,8 F.S. +/- 0,3% absolute value or +/- 3.0% actual value +/- 5% actual value | +/-0,7% +/- 0,1% absolute value or+/- 0.8% actual value | T90 & T10<10s |
Electrochemical sensor | O2 | 0,01% | 1.01-25.00% | +/- 0,1% absolute value or +/- 3.0% actual value | +/- 0,1% absolute value or +/- 1.5% actual value | <40秒from ambient to 0.15 O2 |
Electrochemical sensor | H2S | 1ppm | 0-2000 ppm 0-5000 ppm | +/- 5 ppm absolute value or+/- 3.0% actual value | +/- 5 ppm absolute value 或 +/- 3.0% actual value | T90 & T10<20 s |
Response time | Response time refers to the flow rate of the sample through the gas sample pool at 1L/ min |
Data refresh rate | 1s |
Warm up time | 30 seconds for preparation, 3 minutes for use, and 30 minutes for full operation |
Operation temp. | -10℃ to 70℃ ( 32℉to 158℉) |
Operation humidity | 95% RH (no condensation) |
Operation altitude | -300m to 3000m（-1000至10000ft） |
Communication | USB port (standard) |
Protective housing | IP67(Immerse 1m in 30 minutes） Def Stan 81-41/STANAG 4280 |
Specification
EDK M100BP multi-component biogas analyzer
Battery | 12Vcc Internal charger and charging indicator light |
Display | 5.7-inch resistive touch screen |
Calibration | Optional zero/range calibration or automatic calibration |
Extension power supply | M100BP~240VAC @47~63Hz |
Pneumatic interface | Outside diameter 6.0 inside diameter 4.0 quick plug |
Optional | Humidity sensor, nitrogen measurement, flow measurement, hydrogen |
Weight | 2.5kG |
Other versions of the biogas analyzer
Wall-mounted biological gas analyzer model 6500
19’’ rack type biological gas analyzer EDK M100B
Multi-sampling system used for the biogas analysis system
Based on infrared photoacoustic spectroscopy technology, DKG-ONE Photoacoustic Gas Analyzer combines the unique light source and detector which is a patented enhanced cantilever beam optical microphone with ultra-high sensitivity. It can be widely applied
Transformer online monitoring and fault diagnosis technology is of great significance to improve the safety and stability of the power system.
DK-BSC 3001 series battery spontaneous combustion monitoring system from Duke Technology integrates ultraviolet absorption spectrum, infrared photoacoustic spectrum, cavity enhanced absorption spectrum, Fourier infrared spectrum, tunable semiconductor abs
Ventilation system is to monitor the concentration change of tracer gas to calculate the ventilation efficiency.
SF6 is widely used in GIS as a good insulation and interruption gas.
In oil or gas extraction processes, optimizing production methods is crucial. It is particularly important to accurately understand the flow rates, volumes, flow patterns, and cumulative trends of solid particles during extraction. The sand monitoring sys
The sand monitoring system from Duke integrates the measurement of fluid patterns, flow rate, instantaneous flow, and cumulative flow of sand. It is a low-cost, real-time monitoring system for predicting the flow patterns and cumulative trends of sand.
The sand monitoring system from Duke integrates the measurement of fluid patterns, flow rate, instantaneous flow, and cumulative flow of sand. It is a low-cost, real-time monitoring system for predicting the flow patterns and cumulative trends of sand.
When sand enters the wells or pipelines during the extraction process, it is essential to ensure the clear passage of the sand. Real-time monitoring of the flow rate, instantaneous flow, cumulative flow, erosion rate, and movement patterns of sand/solid p
The sand monitoring system from Duke integrates the measurement of fluid patterns, flow rate, instantaneous flow, and cumulative flow of sand. It is a low-cost, real-time monitoring system for predicting the flow patterns and cumulative trends of sand.
The Duke pigging indicator uses passive acoustic (ultrasonic) technology to sense the pig traveling through the pipeline, utilizing a built-in Lock Frequency Digital Signal Processor (LPDSP).
The DK-SA 830 Gas-Solid Separator operates on the principles of centrifugal sedimentation and density differences. When the fluid enters the separator tangentially at a certain pressure, it generates intense rotational motion.
Based on echo sensing technology, the Duke Non-intrusive acoustic pipe thickness monitor uses high-frequency sound waves generated by piezoelectric transducers to pass through materials.
The innovative DK-SA 850 downhole sand monitoring device features a new tool architecture, integrating advanced sensor design, signal processing technology, and analytical algorithms to accurately detect downhole sand ingress points and assess sand produc
DK-SA 860-S Series Vibration Sensor can connect to analog signal output of acceleration, speed, displacement sensors, can calculate speed and displacement data based on acceleration data, features include different sensor parameter settings, data acquisit
